Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Duct Repair & Sealing in Sandy Springs: What to Know First
We provide independent Abatement Technologies duct repair and sealing in Sandy Springs with written prices delivered before any work starts and a documented photo record of every duct run. Most Abatement Technologies repairs we handle are completed in a single visit, with turnaround depending on parts availability for your specific series. This page is for homeowners who own an Abatement Technologies air filtration or abatement system connected to residential ductwork and have noticed uneven airflow, rising utility bills, or visible damage at the plenum connection. Call (678) 904-9744 for a free estimate with a written price.
How Abatement Technologies Products Fail - and How We Fix Them
- CAP600-series plenum seal degradation. The CAP600 whole-house air cleaner uses a pressed-metal plenum adapter that sits between the unit and your trunk line. After five to seven years in Sandy Springs’ humidity cycle, the factory gasket compresses and the mastic sealant behind it cracks. We remove the adapter, clean the mating surface to bare metal, and reseal with fresh mastic rated for the CAP600’s static pressure - not generic caulk that will dry-shrink within a season.
- PRED1200 flex duct collapse at the HEPA bypass. The PRED1200’s bypass damper creates a pressure spike when the HEPA stage engages. In Sandy Springs homes built on crawl spaces, we’ve found the flex duct between the unit and the main trunk has flattened at the first elbow, choking airflow to the second floor. We replace the collapsed section with reinforced flex duct and add a support strap at the elbow to prevent recurrence - the photo comes first. The invoice comes second.
- HVAC5000 series metal duct seam separation. The HVAC5000’s high-velocity output exposes weak points in older metal ductwork, particularly at longitudinal seams sealed with tape rather than mastic. We see this most in Sandy Springs ranch homes from the 1970s where the original ductwork predates the Abatement Technologies install. Our fix: peel the failed tape, clean with solvent, and reseal the seam with brush-applied mastic reinforced with mesh - a permanent repair, not a patch.
- BD2KL negative air machine duct adapter fatigue. The BD2KL’s rigid duct adapter, used when the unit is integrated into permanent ductwork for remediation jobs, develops stress cracks at the bolt holes after repeated cycling. We fabricate a replacement adapter from heavier-gauge galvanized steel or source the OEM part depending on your warranty status and how long you plan to keep the unit in service.
- Abatement Technologies inline filter housing air leaks. The gasket channel on inline housings like the FAS1-2000 can warp if overtightened during filter changes, breaking the seal and pulling unfiltered attic air into the system. We measure the gap, machine a replacement gasket or replace the housing lid if the channel is damaged, and photograph the pressure test to confirm zero bypass.
Our Abatement Technologies Duct Repair & Sealing Process
- 1
Inspection with photo documentation. We access the ductwork at the plenum, each register, and the Abatement Technologies unit connection. Every run is photographed before any tool touches it.
- 2
Written scope and price. Tomas Reyes or a senior technician delivers a written repair scope with line-item pricing under Haven Standard Clause 1. No work begins until you have the price in hand.
- 3
Parts decision: OEM or quality aftermarket. For units under warranty, we use Abatement Technologies OEM adapters and gaskets to preserve coverage. For out-of-warranty systems, we source equivalent aftermarket parts from Guardsman and Honeywell lines and document the substitution in writing.
- 4
Repair and reseal. We execute the repair - flex duct replacement, metal seam mastic, plenum reseal, or adapter fabrication - and run a negative-pressure extraction to clear debris before closing access.
- 5
Pressure test and photo record delivery. We test static pressure at the unit and photograph every repaired run after completion. You receive the full photo record as a standard deliverable, not an extra.
- 6
365-Day Done Right Promise activation. The written guarantee goes into your job record. If the seal fails or the repair doesn’t hold, we make it right.
BeforeAfterWhat Abatement Technologies Duct Repair & Sealing Costs in Sandy Springs
Abatement Technologies duct repair and sealing in Sandy Springs typically runs $340-$780 for most residential jobs we handle. A single plenum reseal on a CAP600 series falls at the lower end. Flex duct replacement on a PRED1200 with multiple elbows runs higher due to labor and reinforced material. Metal duct seam repair on HVAC5000-integrated systems lands in the middle, with cost driven by linear feet of seam and attic access difficulty.
What moves the price: whether we can reach the repair point from a basement or must work a Sandy Springs crawl space in July; whether the unit is under warranty and requires OEM parts; and whether the original installer left adequate service clearance around the Abatement Technologies housing. We do not quote per-vent pricing. One flat price per system, agreed in writing before work starts. Call (678) 904-9744 for an exact quote - estimates are free.
Why Sandy Springs Homeowners Call CleanRun Air Duct Cleaning Sandy Springs for Abatement Technologies Work
We’ve been working Sandy Springs since 2013, including repeat jobs in the Spalding Drive corridor where ranch homes hide ductwork that hasn’t been touched since the Carter administration. Tomas Reyes and our crew know the Abatement Technologies product line from hands-on repair work, not from a distributor brochure. When a CAP600 plenum adapter cracks or a PRED1200 bypass flattens flex duct, we’ve likely seen the exact failure before and photographed it.
Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews. We also service Lennox, Trane, and Carrier systems, so when an Abatement Technologies unit is integrated with a mixed-manufacturer HVAC setup, we don’t guess at the interaction. Every job carries the 365-Day Done Right Promise in writing, and every estimate can be compared against a competitor’s written quote through our Free Second Opinion.
FAQs
Independent repair does not automatically void the warranty, but using non-OEM parts on a covered unit can. We source OEM adapters and gaskets for in-warranty systems and document aftermarket substitutions in writing for out-of-warranty units so you know exactly what was used. Call (678) 904-9744 to discuss your specific model and warranty status.
You receive a documented photo record of every duct run before and after repair, plus static pressure readings taken at the Abatement Technologies unit. If the photo doesn’t show fresh mastic or a replaced flex section, the work didn’t happen - our record is your verification.
Repair makes sense when the duct damage is localized and the Abatement Technologies unit itself is performing within manufacturer specs. We recommend replacement when the unit is past its service life or when repair costs exceed 60% of a new integrated system. Tomas Reyes will show you the inspection photos and run the numbers in writing before you decide.
Most single-point repairs - a plenum reseal, one flex duct replacement, or metal seam repair - are completed in two to four hours. Jobs requiring OEM parts we don’t stock add one to two business days for shipping. We give you a written time estimate with the price, not a vague window.
The $79 coupon model typically covers a visual look and a pass with a shop vac, not actual repair or sealing. We quote the full scope: access, repair, materials, pressure test, photo documentation, and the 365-Day Done Right Promise. The written price is the price - no invoice inflation once the truck is in your driveway.
Ready to see what your Abatement Technologies ductwork actually looks like? Call (678) 904-9744 for a free estimate with a written price before any work starts. We’ll bring the camera first.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Sandy Springs at CleanRun Air Duct Cleaning Sandy Springs, serving Sandy Springs and nearby areas.