Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Air Quality & Sanitizing in Sandy Springs: What to Know First
We provide independent Abatement Technologies air quality and sanitizing service in Sandy Springs, with most jobs scheduled within a week and completed in a single visit. A typical whole-system sanitizing job runs $380-$620 for Abatement Technologies equipment, and we put that price in writing before any work starts. This page is for homeowners running Abatement Technologies HEPA filtration, negative air machines, or portable scrubbers who need mold treatment, bacteria sanitizing, odor removal, or UV light installation done by technicians who know the equipment line by line. Call (678) 904-9744 for a free estimate with no obligation.
How Abatement Technologies Products Fail - and How We Fix Them
- PREDATOR 600 series HEPA units develop blower motor strain in Sandy Springs’ extended pollen season. The 600-series pulls 600 CFM through dense HEPA media, and March through May in north Fulton County loads filters faster than the national spec sheet assumes. We photograph the filter loading before removal, replace with OEM Abatement Technologies media or verified equivalent, and check amp draw on the blower to confirm it’s not working harder than designed.
- H2000i portable scrubbers show UV-C lamp degradation after 18-24 months of intermittent use. The lamp sleeve fogs with biofilm that blocks 254nm output even when the indicator light still glows. We meter actual UV output with a radiometer, not just visual inspection, and replace lamps with Abatement Technologies-specified 36W T5 UV-C tubes or documented equivalents that maintain warranty compliance.
- AIR SCRUBBER HEPA 1000 units accumulate condensate in the plenum during Sandy Springs summer months. When relative humidity stays above 75% for weeks, the aluminum plenum sweats and cultivates mold at the filter seal edge. We disassemble the plenum, treat with EPA-registered antimicrobial, and reseal with closed-cell gasket material rated for HVAC wet environments - not hardware-store foam tape.
- BD2KM duct-mounted negative air machines lose seal integrity at the flex-duct connection. The factory clamp loosens with thermal cycling in attic installations common to Spalding Drive corridor ranches. We replace with stainless-steel constant-tension clamps and document the static pressure reading before and after to verify no bypass.
- Abatement Technologies HEPA filters in remodel environments clog with construction particulate that voids warranty coverage. Fine drywall dust loads the pleats unevenly and can collapse the media pack. We inspect for loading pattern, photograph the evidence, and install temporary pre-filtration or recommend upgrade to the Abatement Technologies RAPID ARCH line if the application demands it.
Our Abatement Technologies Air Quality & Sanitizing Process
- 1
Scheduled arrival with named technician. Haven Standard Clause 3: Verified Crews. You get the technician’s name 24 hours ahead. Tomas Reyes or a background-checked, uniformed crew member arrives in a marked CleanRun vehicle.
- 2
Visual and photographic documentation before equipment moves. We photograph the Abatement Technologies unit in place, filter condition, and any visible contamination. The photo comes first. The invoice comes second.
- 3
Written scope and price delivered before work begins. Haven Standard Clause 1. We specify OEM vs. quality aftermarket parts for your Abatement Technologies model, the sanitizing agent and method, and the total. No per-vent add-ons, no surprise line items.
- 4
Service execution with trade-grade tools. We use Abatement Technologies-compatible equipment from our roster - Rotobrush for duct contact cleaning, Nikro for negative-pressure extraction when needed, and Guardsman-sourced antimicrobial agents registered for HVAC application.
- 5
Post-service testing and photo record delivery. UV output metered, static pressure confirmed, before-and-after photos of every duct run and component. The documented photo record is included as a standard deliverable, not an upsell.
- 6
365-Day Done Right Promise activated in writing. If the odor returns, the mold recurs, or the UV lamp fails prematurely, we make it right. The guarantee is a written document, not a verbal assurance.
BeforeAfterWhat Abatement Technologies Air Quality & Sanitizing Costs in Sandy Springs
| Service | Typical Range | What Moves the Price |
|---|---|---|
| HEPA filter replacement + blower service (PREDATOR 600 series) | $180-$290 | Filter type (OEM vs. verified equivalent); attic vs. basement access |
| UV-C lamp replacement + output verification (H2000i) | $220-$340 | Single lamp vs. dual-lamp configuration; sleeve condition |
| Whole-system mold treatment + antimicrobial seal (AIR SCRUBBER HEPA 1000) | $380-$620 | Contamination extent; plenum disassembly required; duct run count |
| Negative air machine reseal + static pressure test (BD2KM) | $260-$410 | Flex-duct length; clamp count; accessibility in finished spaces |
| Odor remediation with ozone or hydroxyl treatment | $340-$550 | Source location; treatment duration; post-treatment verification testing |
These are whole-system prices agreed before work starts. We do not quote per-vent or per-filter pricing that balloons on arrival. Sandy Springs’ older ranch homes on Spalding Drive and the higher-humidity zones near the Chattahoochee River often need more extensive plenum treatment than newer construction - we price for what we find, but we find it before you commit. Call (678) 904-9744 for an exact quote. Estimates are free.
Why Sandy Springs Homeowners Call CleanRun Air Duct Cleaning Sandy Springs for Abatement Technologies Work
We’ve been working Sandy Springs since 2013, and the Abatement Technologies equipment we see most - the PREDATOR line in remediation contractor vans, the H2000i units in medical office retrofits, the BD2KM systems in older homes near Hammond Park - has specific failure patterns that change with this zip code’s humidity and construction era. Tomas Reyes and our crew know the difference between a filter that needs changing and a blower that’s overamping because of it.
Our 365-Day Done Right Promise applies to every Abatement Technologies job. The documented photo record shows you what was inside your ducts before we touched them and what remained after. We’re also equipped to service Lennox, Trane, and Carrier systems when your home has mixed equipment - no need to coordinate multiple contractors. Haven Standard Clause 1 means the price you agree to is the price you pay. Haven Standard Clause 3 means the person who arrives has been verified and named.
FAQs
No, when performed by a trained technician using manufacturer-compatible parts and EPA-registered agents. As an independent Abatement Technologies service provider, we document every product and method for warranty compliance. Using unregistered chemicals or non-specified UV lamps can void coverage, which is why we specify OEM or verified equivalents in writing. Call (678) 904-9744 if you need documentation for a warranty claim.
Replacement makes sense when repair exceeds 60% of replacement cost or when the unit lacks current filtration standards. We evaluate motor amp draw, housing integrity, and filter availability for your specific series. A PREDATOR 600 with a seized motor and corroded plenum is usually a replacement; an H2000i with lamp and sleeve wear typically merits repair. We put both numbers in writing so you decide from evidence, not pressure. Call for a free assessment.
We deliver a documented photo record of every duct run and component, plus post-treatment verification - UV output in microwatts per square centimeter, static pressure differential, or visual inspection of treated surfaces. The 365-Day Done Right Promise covers recurrence. If you don’t receive documentation, the job isn’t finished. Call (678) 904-9744 to schedule a documented service.
Most residential jobs run 2.5 to 4.5 hours depending on system size and contamination level. A single H2000i UV lamp change takes under 90 minutes. Whole-system mold treatment with antimicrobial seal on an AIR SCRUBBER HEPA 1000 in a Sandy Springs ranch home with attic ductwork typically takes a full morning. We schedule start times, not vague windows, and call 30 minutes before arrival.
Yes. We maintain cross-reference documentation for discontinued Abatement Technologies series and stock compatible filters, lamps, and seals from Guardsman and other trade-recognized suppliers. For obsolete negative air machines, we can often retrofit with current-spec components that meet or exceed original performance. We document compatibility in writing before installation. Call with your model and serial number for availability.
Ready to see what’s actually inside your Abatement Technologies system? Call (678) 904-9744 for a free estimate with a written price delivered before any work begins. We serve Sandy Springs and nearby north Fulton County communities.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Sandy Springs at CleanRun Air Duct Cleaning Sandy Springs, serving Sandy Springs and nearby areas.