Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Sandy Springs: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Sandy Springs with written upfront pricing and a documented photo record on every job. Most Abatement Technologies evaporator coil and blower cleanings are completed in a single visit, with your written price delivered before any panel comes off. As an independent Abatement Technologies service provider, we are not affiliated with or authorized by Abatement Technologies, but our technicians service these units regularly in Sandy Springs homes from the Spalding Drive corridor to the newer builds near City Springs.
This page is for homeowners who own an Abatement Technologies air handler, furnace, or heat pump and need the coil, blower, or heat exchanger cleaned properly - not a shop-vac waved near a register. If you are researching what the work should cost, what can go wrong with your specific unit, and how to verify the work was actually done, you are in the right place. Call (678) 904-9744 for a free estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- HEPA-AIRE portable air scrubbers (PAS series) - blower wheel imbalance from fine particulate buildup. In Sandy Springs, these units often run during whole-home renovations where Georgia clay dust and drywall particulate coat the blower vanes unevenly. The PAS2400 and PAS5000 models develop a telltale harmonic vibration at 1,200 RPM when the leading edge of the wheel loads up. We remove the blower assembly, clean each vane with negative-pressure extraction, and photograph the runout measurement before reassembly. The photo comes first. The invoice comes second.
- Abatement Technologies PREDATOR series - evaporator coil fin corrosion from condensate pan chemistry. The aluminum fins on PREDATOR 600 and 800 units react with standing condensate in Sandy Springs homes where the pan drain line pitches incorrectly. We see this especially in 1970s ranch conversions on Spalding Drive where the original slab settling threw the drain slope off by degrees. Our cleaning includes pan removal, fin straightening where possible, and a written note on drain line pitch for your HVAC contractor.
- Abatement Technologies HEPA filtration modules - filter bypass from frame seal degradation. The gasket material on HEPA500 and HEPA2000 modules stiffens after 18-24 months in Georgia’s cooling-season humidity, creating a bypass path that defeats the filter entirely. We document the seal condition with pre-cleaning photos, replace gaskets with quality aftermarket material where OEM is backordered, and pressure-test the seal before close-up.
- Abatement Technologies duct-mounted UV systems - quartz sleeve fouling that reads as “lamp failure.” Owners in Sandy Springs often replace the $180 UV lamp twice before realizing the quartz sleeve has accumulated a biofilm layer the lamp cannot penetrate. We clean sleeves with a dedicated quartz-safe process, measure UV-C output at the plenum with a radiometer, and show you the before/after microwatt reading. No lamp replacement needed in roughly 60 percent of “dead lamp” calls we see.
- Abatement Technologies CAP series negative air machines - motor bearing contamination from improper inlet pre-filtering. CAP600-UV and CAP1200 units suffer bearing wear when coarse pre-filters are skipped or installed backward, allowing construction debris to reach the motor housing. We disassemble the inlet plenum, clean the bearing housing with solvent and compressed air, and photograph the pre-filter orientation on reassembly so your crew can verify proper installation going forward.
Our Abatement Technologies HVAC Cleaning Process
- 1
Diagnostic photo set before equipment moves. We photograph the unit nameplate, the coil face, the blower housing, and any visible debris - before a panel comes off. This is Haven Standard Clause 1: Written Price Before Work Starts. You see what we see.
- 2
Written scope and price delivered. We itemize the cleaning required, note any parts condition (gaskets, sleeves, filters), and give you one flat price per system. No per-vent add-ons, no “once we’re in there” surprises.
- 3
OEM-vs-aftermarket parts decision documented. For Abatement Technologies units, we stock common gaskets and sleeves; for backordered OEM items, we specify the quality aftermarket equivalent in writing with warranty implications noted.
- 4
Negative-pressure extraction cleaning with Rotobrush and Abatement Technologies-compatible tools. Coils are cleaned with foaming agent and low-pressure rinse; blowers are removed and cleaned outside the unit to prevent debris redistribution; heat exchangers are inspected with borescope and brushed where accessible.
- 5
Post-cleaning test and photo record delivery. We run the unit through a full cycle, measure temperature split and static pressure where applicable, and deliver your Documented Photo Record - before/after of every cleaned component - as a standard job deliverable, not an extra.
- 6
365-Day Done Right Promise activation. Your written guarantee goes into the job file. If the work is not right, we make it right. This is backed in writing, not subject to manager approval.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Sandy Springs
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (Abatement Technologies air handler or heat pump) | $340-$520 | Coil accessibility (A-coil vs. slab), fin corrosion severity, whether pan removal is required |
| Blower assembly removal and cleaning | $280-$410 | Blower size (PAS series vs. standard residential), wheel imbalance correction needed |
| Heat exchanger cleaning and inspection | $260-$390 | Number of cells, accessibility through burner compartment, brushing vs. chemical cleaning |
| Condenser coil cleaning (outdoor unit) | $220-$340 | Refrigerant line length to outdoor pad, fin density, surrounding debris (pine straw, cottonwood) |
| UV quartz sleeve cleaning and output test | $180-$260 | Number of sleeves, sleeve replacement vs. cleaning, radiometer verification included |
| Full system HVAC cleaning (coil, blower, heat exchanger, condenser) | $780-$1,150 | System tonnage, component count, documented photo record included as standard |
Prices reflect Sandy Springs market rates for documented, professional-grade work - not a coupon special that becomes a $900 invoice once the van arrives. Every price is written and agreed before work starts. Call (678) 904-9744 for your exact quote; estimates are free.
Why Sandy Springs Homeowners Call CleanRun Air Duct Cleaning Sandy Springs for Abatement Technologies Work
We have cleaned Abatement Technologies equipment in Sandy Springs since 2013, including jobs where the unit had not been opened in fifteen years. Tomas Reyes and our crew know the difference between a PAS series blower and a standard residential wheel, and we stock the gaskets and sleeves that Abatement Technologies units actually need - not generic substitutes that fail in six months.
Our equipment roster includes Rotobrush, Nikro, Abatement Technologies, Honeywell, Aprilaire, and Guardsman - brands you can look up and verify. We also service Lennox, Trane, and Carrier systems, so multi-brand homes get consistent documentation across every unit. Every technician is background-checked and uniformed under Haven Standard Clause 3: Verified Crews. You get a name before anyone arrives.
The 365-Day Done Right Promise, the written price before work starts, and the Documented Photo Record on every visit are not marketing language. They are the terms under which we operate, backed by 52,000+ jobs where the customer saw the evidence before paying.
FAQs
No, professional cleaning by an independent service provider does not void your Abatement Technologies warranty, provided no components are altered or damaged during the work. We document the unit’s pre-existing condition with photos before touching anything, and we use manufacturer-compatible cleaning agents - not caustic chemicals that attack aluminum fins or gasket materials. If your unit is still under warranty, we note the serial number and service date in your job record for your files. Call (678) 904-9744 if you need help locating your warranty terms.
You receive a Documented Photo Record of every cleaned component - coil face before and after, blower housing, heat exchanger inspection images, and any parts replaced - as a standard deliverable on every job. We have held this practice since our first job in 2013. If a company cannot show you the inside of your own ducts and coils, they are selling you vacuum noise and confidence. We sell evidence.
Clean if the coils and blower are structurally sound and the unit is under fifteen years old; replace if the heat exchanger is cracked, the coil has pinhole leaks at multiple points, or repair costs exceed 40 percent of replacement. We give you the photograph that shows which condition applies. In Sandy Springs, we see Abatement Technologies PREDATOR units from the early 2000s still running well after proper cleaning; we also see neglected units where fin corrosion has progressed too far. The photo makes the decision obvious. Call (678) 904-9744 for an honest assessment.
A single-component cleaning - coil or blower - typically takes 2 to 3 hours on-site. A full system cleaning runs 4 to 5 hours. We do not rush the diagnostic photography or the post-cleaning test cycle. Your written price does not change if the job runs long.
We stock common Abatement Technologies gaskets, sleeves, and filters; for specialized components, we source quality aftermarket equivalents when OEM is backordered and document the substitution in writing. We do not guess at compatibility. If a part is needed that we cannot verify, we stop and show you the photograph before proceeding. Haven Standard Clause 1 applies: written price before work starts, even for mid-job discoveries.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Sandy Springs at CleanRun Air Duct Cleaning Sandy Springs, serving Sandy Springs and nearby areas.