Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterFast, Reliable Duct Repair & Sealing Across Milton
Duct repair and sealing in Milton, GA typically runs $340-$1,200 per system depending on access, material type, and whether we’re sealing accessible joints or replacing collapsed flex runs. Most Milton estate homes need two to three separate systems addressed, and our Duct Repair & Sealing crew quotes each one independently so you’re not paying for zones that don’t need work. Crews dispatch from our Atlanta office and carry Rotobrush and Nikro equipment sized for the large custom homes that dominate Milton’s market. Call (678) 904-9744 and we’ll put a written price in your hand before any panel comes off.
Why CleanRun Air Duct Cleaning Sandy Springs Is Milton’s Preferred Duct Repair & Sealing Company
We’ve been working in Milton since we started serving north Fulton County in 2013. The homes here are different from what we see in Sandy Springs or Roswell - larger square footage, multi-zone systems, and duct runs that span three stories plus finished basements. That difference matters when you’re pricing repair work.
Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews. We identify each crew member by name before arrival. Every job starts with a written price and ends with a Documented Photo Record - inside every duct run, before and after - delivered as part of the standard job record. No manager approval needed. No “call for pricing.”
The 365-Day Done Right Promise applies to every Milton job in writing, not just in marketing copy. If the sealing fails or a repaired flex run collapses again, we make it right.
Our Duct Repair & Sealing Services in Milton
Duct Sealing
Most Milton homes built during the 2000s-2010s boom have extensive metal trunk lines with dozens of takeoff joints. Each joint is a potential leak point. We pressurize the system, locate leaks with smoke testing or digital manometers, then seal accessible joints with mastic sealant or metal-backed tape rated for HVAC use. For a typical 4,000-square-foot Milton home with two systems, duct sealing runs $480-$890 per system. We clean the duct interior first - North Georgia pollen leaves a sticky film that prevents proper mastic adhesion if you seal over it.
Flex Duct Repair
Flex duct is common in Milton’s finished basements and attic drops. The inner liner degrades faster when return air carries heavy particulate loads - horse dander, hay dust, and the fine grit from pasture roads that equestrian properties deal with. We’ve replaced collapsed flex runs in homes off Birmingham Road where the blower motor was starved for return air and running 30% harder than spec. Flex duct repair in Milton typically costs $280-$650 per run depending on length and access. We use Nikro equipment to verify airflow restoration before we leave.
Metal Duct Repair
Custom homes in the Crooked Creek and Summit Hill areas often have galvanized steel trunk lines with corroded seams or separated slip joints. Metal repair involves cutting out damaged sections, fabricating replacement pieces, and sealing with mastic. This is slower work than flex replacement but holds up better in high-static systems. Metal duct repair in Milton runs $420-$980 per section. We photograph every weld and seam before closing access panels.
Duct Insulation
Uninsulated or degraded duct wrap in Milton’s hot, humid attic spaces costs you cooling efficiency every summer. We install foil-faced fiberglass insulation or closed-cell foam wrap depending on clearance and code requirements. Duct insulation for a typical Milton system runs $560-$1,100. All materials meet current Georgia energy code.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Milton
Our vans stock parts and materials from Honeywell, Aprilaire, and Abatement Technologies - brands you can look up before we arrive. We don’t show up hoping to find what we need. For Milton’s larger homes with Aprilaire zoning panels or Honeywell media filters, this means same-day completion instead of a return trip. The equipment roster is fixed: Rotobrush and Nikro for cleaning and camera inspection, Abatement Technologies negative-pressure extractors for containment, and Guardsman-rated sealants and tapes. You can verify every product before agreeing to the written price.
Common Duct Repair & Sealing Problems We See in Milton Homes
- Zone depressurization from a single disconnected trunk takeoff. In a 6,000-square-foot home with three zones, one bad joint at the main trunk can silently rob an entire floor of conditioned air while the thermostat reads “satisfied.” The homeowner notices only the hot second bedroom or the basement that never cools. We find these with static pressure testing, not guesswork.
- Accelerated flex-duct breakdown from equestrian-property particulate. Horse dander and hay dust are larger, sharper, and more abrasive than typical household dust. They pack into return chases and filter grilles faster, then abrade the inner liner of flex duct from the inside out. Homes along Birmingham Road and the northwest corridors show this pattern reliably.
- Pollen-compromised mastic adhesion. Milton’s dense tree canopy - oaks, pines, and the mature hardwoods that make these lots desirable - drives pollen loads that coat duct interiors with a sticky orange film every April. Seal mastic over that film and it fails within a season. We clean before we seal, every time, and we photograph the surface condition first.
- Collapsed basement flex runs from sharp bends and poor support. Finished basements in Milton’s estate homes often have flex duct routed through soffits with tight 90-degree bends and inadequate hanging straps. Gravity and vibration do the rest. The homeowner blames the air handler. We run a camera and show them the kink.
Pricing for Duct Repair & Sealing in Milton, GA
Here is what duct repair and sealing costs in Milton’s market, based on jobs we’ve completed in the 30004 and 30009 zip codes:
| Service | Typical Range |
|---|---|
| Duct sealing (per system, accessible joints) | $480-$890 |
| Flex duct repair/replacement (per run) | $280-$650 |
| Metal duct repair (per section) | $420-$980 |
| Duct insulation (per system) | $560-$1,100 |
| Mastic sealant application (full system) | $340-$720 |
| Air leak repair at trunk takeoff | $180-$340 |
Three factors move these numbers: access (attic vs. finished basement ceiling), system count, and whether we need to clean before sealing. A single-system 3,200-square-foot home in the central Milton area sits at the lower end. A 7,500-square-foot equestrian property with three systems, finished basement, and pollen-compromised duct interiors sits higher. Every price is written and agreed before work starts - Haven Standard Clause 1. No per-vent pricing. No coupon that doubles on arrival. Call (678) 904-9744 for an exact quote; estimates are free.
We Also Serve Cities Near Milton
Our crews work Milton regularly and also handle duct repair and sealing in Sandy Springs, Roswell, Norcross, and Smyrna. Dispatch and scheduling are coordinated from our Atlanta office. The same written-price protocol, same documented photo record, same 365-Day Done Right Promise applies in every city.
Serving Milton, GA - Our Local Coverage Area
We’re based in the Milton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Duct Repair & Sealing in Milton
Per system. We quote each zone independently because the condition varies. The attic system may need only sealing at six joints; the basement system may need two flex runs replaced. Bundling them into one vague “whole house” price hides what you’re actually paying for each repair. We itemize by system in writing before work starts. Call (678) 904-9744 and we’ll walk through each unit with you.
Yes. Horse dander, hay particulates, and pasture dust infiltrate return-air systems at rates far exceeding typical suburban homes. This abrasive particulate accelerates flex-duct lining breakdown and packs filter grilles faster, which means leaks develop quicker and sealant adhesion is harder to maintain. We factor this into our inspection scope and may recommend more frequent filter changes or upgraded media filtration alongside the repair work. The documentation - the photo record - becomes even more important so you can verify the interior condition yourself.
We test and we photograph. Before sealing, we record static pressure readings at the air handler and smoke-test visible leaks. After sealing, we retest and compare. The photo record shows every sealed joint, every mastic application, every replaced section. You receive this as a standard deliverable, not an extra. Haven Standard Clause 5: Documented Completion. If the numbers don’t improve, we don’t call it done.
It affects preparation, not the sealant itself. Pine and oak pollen deposits a sticky organic film on duct interiors that prevents mastic from bonding to metal. We clean the seam area with mechanical brushing and negative-pressure extraction before applying sealant. Skip this step and the mastic peels within a season. We photograph the cleaned surface before sealing so you can verify it was done right.
Sometimes. If the run is accessible from an adjacent utility room or unfinished storage area, we can often pull new flex through the existing chase. If the collapse is under a finished drywall soffit with no access point, we need to cut a strategic access panel - typically 12 by 12 inches - repair the run, and then patch and paint. We mark the cut location, show you before making it, and include basic patchwork in the written price. Call (678) 904-9744 and we’ll assess access during the free estimate.
Ready for a written price? Call CleanRun at (678) 904-9744. We’ll schedule a free estimate, put the scope and price in writing before any work starts, and leave you with a documented photo record of every duct run we touched. The 365-Day Done Right Promise applies in writing, every time.
Written by Tomas Reyes, Owner at CleanRun Duct Repair & Cleaning, serving Milton and north Fulton County since 2013.